Ametek i Series User Manual Page 316
- Page / 341
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
User Manual
302 i Series / iX Series
Sub-Tab
Description
phase to be displayed, one at a time.
Additional user controls located on the EUT Performance Measurements Tab:
Control / Display
Description
Update Meas.
Triggers a new acquisition cycle and updates measurement data for all tabs. For
table C mode (Variable Frequency), data will be acquired at the frequency set by
the Test Frequency Dropdown control.
This button is always available regardless of what sub tab is selected.
Settings
Brings up a dialog box that allows scaling and color changes for the Waveform or
Current harmonics graphs. Note that setting changes will apply to graphs for all
phases.
For current harmonics graphs, only the absolute bar settings apply. The ABD
measurement screen does not display relative current harmonic bar charts but
relative data is available in tabular format on the Cur Spectrum tab.
This button is available only if either the Waveforms or Cur Graph sub tab is
selected
- AC Power Source 1
- User Manual 1
- SAFETY SYMBOLS 7
- 1. Introduction 15
- 2. Specifications 16
- 2.2 Mechanical 24
- 2.3 Environmental 24
- 2.4 Regulatory 26
- 2.5 Front Panel Controls 26
- 3.1 Unpacking 29
- 3.2 Power Requirements 29
- 3.3 Mechanical Installation 30
- 3.4 Input Wiring – TB1 30
- 3.6 Connectors - Rear Panel 32
- Description 33
- Centronics 36
- Connector 36
- > 400 uS 36
- 24 i Series / iX Series 38
- 3.8 Output Voltage Ranges 40
- 3.9 Functional Test 41
- 28 i Series / iX Series 42
- 30 i Series / iX Series 44
- 34 i Series / iX Series 48
- 4. Front Panel Operation 51
- FUNCTION 53
- 4.2 Menu Structure 56
- 44 i Series / iX Series 58
- 4.2.2 Overview of Menu 1 58
- 4.3 Output Programming 91
- 4.5 Standard Measurements 97
- 4.7 Transient Programming 108
- 5. Principle of Operation 115
- 5.2 Overall Description 116
- 5.3 Oscillator Assembly 116
- 104 i Series / iX Series 118
- 5.4 Current Limit Board 119
- 5.5 Auxiliary Power Supply 119
- 5.6 DC-DC Power Converter 120
- 5.7 AC Control Logic 120
- 108 i Series / iX Series 122
- 5.8 AC Power Board 123
- 5.9 Input/Output Board 123
- 110 i Series / iX Series 124
- CAUTION 126
- 6. Calibration 127
- 118 i Series / iX Series 132
- 6.6 Non-Routine Calibration 134
- 124 i Series / iX Series 138
- 7. Service 139
- 9. Options 147
- 138 i Series / iX Series 152
- Refer to 157
- 158 i Series / iX Series 172
- 9.1.2.8 160 Test Selection 172
- 164 i Series / iX Series 178
- 168 i Series / iX Series 182
- 170 i Series / iX Series 184
- 172 i Series / iX Series 186
- 174 i Series / iX Series 188
- 176 i Series / iX Series 190
- 178 i Series / iX Series 192
- 9.2 IEC 61000-4-11 Option 194
- 9.3 IEC 61000-4-13 Option 201
- 196 i Series / iX Series 210
- 9.4 EOS Option 213
- 206 i Series / iX Series 220
- 208 i Series / iX Series 222
- Figure 9-39: 15003iX/3-EOS3 222
- 9.5 Mode iX Option 228
- 218 i Series / iX Series 232
- 9.6 Omni Options 236
- 226 i Series / iX Series 240
- 228 i Series / iX Series 242
- Power Switch and Lamp 244
- 80-250V SYNC INPUT FROM iX 250
- SOURCE INPUT,OR 250
- OTHER AC LINE VOLTAGE 250
- 9.8.2.8 704 Test Selection 273
- 260 i Series / iX Series 274
- 262 i Series / iX Series 276
- 266 i Series / iX Series 280
- 268 i Series / iX Series 282
- 270 i Series / iX Series 284
- 272 i Series / iX Series 286
- 274 i Series / iX Series 288
- 276 i Series / iX Series 290
- 278 i Series / iX Series 292
- 280 i Series / iX Series 294
- 282 i Series / iX Series 296
- 284 i Series / iX Series 298
- 286 i Series / iX Series 300
- 9.9.7 ABD Test Selection 309
- 296 i Series / iX Series 310
- 298 i Series / iX Series 312
- 302 i Series / iX Series 316
- Controls 319
- 308 i Series / iX Series 322
- 310 i Series / iX Series 324
- 312 i Series / iX Series 326
- 314 i Series / iX Series 328
- 9.10 WHM Option 331
- 10. Error Messages 334
- 322 i Series / iX Series 336
- 324 i Series / iX Series 338
- Table 10-1: Error Messages 338
- 11. Index 339
Related products and manuals for Equipment Ametek i Series
Equipment Ametek MX CTSL User Manual
(157 pages)
(157 pages)
Equipment Ametek i-iX Series II User Manual
(258 pages)
(258 pages)
Equipment Ametek GUPS 2400A-107 User Manual
(36 pages)
(36 pages)
Equipment Ametek HPD Series User Manual
(58 pages)
(58 pages)
Equipment Ametek APG-XT User Manual
(36 pages)
(36 pages)
Equipment Ametek LPDC-16V User Manual
(4 pages)
(4 pages)
Equipment Ametek PLA-PLW User Manual
(128 pages)
(128 pages)
Equipment Ametek LPDC-65V User Manual
(4 pages)
(4 pages)
Equipment Ametek HPDC-450V User Manual
(3 pages)
(3 pages)
Equipment Ametek FPDC User Manual
(4 pages)
(4 pages)
Equipment Ametek ACPS User Manual
(4 pages)
(4 pages)
Equipment Ametek HPAL User Manual
(3 pages)
(3 pages)
© 2020, manymanuals.com. All rights reserved. | 0.984 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals